uks3rnse8L

I am currently attempting to fit the new style flat bottom steering wheel with multi function control to my 2003 8L s3.


so far i understand this is possible by attaching a a4 scsm part no: 8E0 953 549 R to the LIN bus parts of the A4 steering module, the CAN bus section and then tie these parts into the A3 CAN bus system and steering module.

would anyone know where i could find the a4 wiring schematics so i can figure out how to connect up the a4 steering coloumn electrics?
Any help or pointers will be very much appreciated.

__________________
Audi 2003 S3 8L, RNS-E 2007 s/w660, VIM,SDS, DVD, Alpine dvb-t, Kauftec control

Borys182

Hi
I fit the steering wheel audi s3 8p to S3 8l 2002. I bought a multifunktion module (4B0 907 487F) after etka, and I do not know where it is set up correctly. Where it should be plug in?Does this have any chance to work? Please help

uks3rnse8L

yes this is possible as it is fitted and fully working in my 8L s3, it works perfectly with the rns-e and audi bluetooth module i have also retro- fitted. one major problem was the new steering wheel airbag is dual stage and the 8L operates on a single stage ignition. This i had to overcome by rewiring but i some times get a fault code for the steering wheel airbag of "low resistance". Apart from this everything else works perfectly.

__________________
Audi 2003 S3 8L, RNS-E 2007 s/w660, VIM,SDS, DVD, Alpine dvb-t, Kauftec control

Borys182

Thank you very much for your reply. Tell me what I need? Do you have any diagrams? Airbag problem already solved.

Borys182

Which module you used? I plugged the module from Audi A6 and Audi A3 8l (etka info), but it does not work correctly. Only the buttons are backlit as this module needs old steering wheel with a small built-in module in the steering wheel. Please tell me which module to connect and can you give me a pinout or scheme. thx

jellyer

I fit the steering wheel audi s3 8p to S3 8l 2002.

__________________
If women are expected to do the same work as men, we must teach them the same things.<a href="http://www.buyterracottawarriors.com">buy terracotta warriors</a>

Borys182

back:


1 - Terminal 31 - brązowy (masa)
2 - Terminal 30 - czerwono-żółty (+) (bezpiecznik 13)
5 - Cruise control switched “Off” - niebiesko-zielony
6 - Alarm (special-purpose vehicles)
7 - Radio telephone (special-purpose vehicles)
8 - CAN Bus Low (convenience) - pomarańczowo-brązowy
9 - CAN Bus High (convenience) - pomarańczowo-zielony
10 - CAN Bus High (drive train) - pomarańczowo-czarny
11 - CAN Bus Low (drive train) - pomarańczowo-brązowy
12 - Ignition lock terminal 75 - żółto-czarny
13 - Ignition lock S contact - czarny (prawdopodobnie stały plus z akumulatora)
14 - Ignition lock terminal 15 - czerwony (prawdopodobnie plus po kluczyku) - do sprawdzenia miernikiem
15 - Ignition lock terminal 50 - niebieski
16 - Ignition lock terminal P - szaro-żółty






A - Connector for cruise control system
1 - Terminal 31
2 - Fix
3 - Distance
4 - Terminal 30
5 - Resume/touch function (Off)
6 - Acceleration/deceleration
7 - Locked (Off)
B - Connector for turn signal
1 - Terminal 31
2 - Radio telephone (special-purpose vehicles)
3 - Alarm (special-purpose vehicles)
5 - Headlight flasher/light control
6 - Turn signal indicators
C - Connector for multi-function steering wheel /
tiptronic / heated steering wheel
7 - tiptronic (–)
8 - Multi-function steering wheel (terminal 30)
9 - Multi-function steering wheel (LIN data bus)
10 - Heater sensor/ tipronic (+)
11 - Multi-function steering wheel dimmer
12 - Tiptronic earth
13 - Steering wheel heating (+)
14 - Steering wheel heating (–)

D - Steering angle sender -G85-
1 - Light barrier 5
2 - Light barrier 3
3 - Light barrier 1
4 - Terminal 30
5 - Voltage supply (5 V)
6 - Light barrier 6
7 - Light barrier 4
8 - Light barrier 2
9 - Terminal 31
10 - Light barrier 7
E - Horn -H1-
1 - Terminal 31
2 - Horn
F - Wiper system
1 - Terminal 31
2 - Intermittent wipe potentiometer
3 - On-board computer
5 - Wash
6 - Wipe

Colours are in polish but not important.
Most i know. Cant get the aftermarket module ( 8E0 953 549 R or Q) anywhere to finish this

Il Signor Zetec

Hello, which A6 code did you use? I don't understand why it in your car doesn't work.
bye

__________________
http://img.photobucket.com/albums/v2...irma_atina.jpg
Audi S3 8L MY 2001 AMK: white Recaros, GRA tempomat, RNS-E, TT pedals, S3 mats, turbo gauge, K&N panel filter

Borys182

I need the help.
trying to connect the module from the audi s3 8p to s3 8l. The rear plugg:
CAN Bus Low convenience
CAN Bus High convenience
Terminal 30 - red / yellow (+)
Terminal 31 - brown (ground)
still i've got 3 wires left:
black/white
black
red/balck - probably the ignition 12V

the front of the module I connected MFSW L-bus data and power to the steering wheel

Still not working. I hope that because the remaining 3 wires at the back.
Do I have to connect
CAN Bus High (drive train)???
CAN Bus Low (drive train)???
and where to connect the remaining 3 wires
does is it have a chance to work?
cheers

PetrolDave

The CAN bus connections must be made to the Convenience CAN , definitely NOT to the Powertrain CAN.

Don't know about the other 3 wires - colours don't mean a lot because they can change from model year to model year, what pins are they connected to?

__________________
06 RS4 Avant - Phantom Black

2010 EU RNS-E 8P0 035 193 C with A4 faceplate - with SDS (HW 070, SW 0150) - coded 309723
16GB SDHC card + CD changer and AMI ready to be fitted

BT 8P0 862 335 M - coded 10702 paired with HTC TyTN II (WM6.1)

Instruments ch 62 = 23
VCDS (VAG-COM) 908 + HEX-COM+CAN